Le clavier mécanique (Aukey KM-G9) ne fonctionne pas après la suspension. Ubuntu Gnome 17.04
Lorsque je mets mon ordinateur de bureau en veille, je reprends mon clavier (Aukey KM-G9) lorsque je le reprends. Si je débranche puis que je le rebranche, alors cela fonctionne. J'utilise actuellement Ubuntu Gnome 17.04, mais j'ai le même problème avec 16.04.
Edit: j'ai essayé mon ancien clavier et cela fonctionne après la suspension. Je ne sais pas pourquoi avec mon nouveau j'ai cet étrange problème. Le nouveau est un clavier mécanique.
Voici la sortie lsusb:
Bus 002 Device 003: ID 046d:c246 Logitech, Inc. Gaming Mouse G300
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 005 Device 002: ID 04d9:a0cd Holtek Semiconductor, Inc.
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 002: ID 04e8:6124 Samsung Electronics Co., Ltd D3 Station External Hard Drive
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Voici dmesg
[ 504.725733] PM: Restoring platform NVS memory
[ 504.726015] Suspended for 3.327 seconds
[ 504.726588] Enabling non-boot CPUs ...
[ 504.737759] x86: Booting SMP configuration:
[ 504.737760] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 504.740110] cache: parent cpu1 should not be sleeping
[ 504.740186] microcode: sig=0x306a9, pf=0x2, revision=0x15
[ 504.740448] microcode: updated to revision 0x1c, date = 2015-02-26
[ 504.740515] CPU1 is up
[ 504.749709] smpboot: Booting Node 0 Processor 2 APIC 0x4
[ 504.752082] cache: parent cpu2 should not be sleeping
[ 504.752502] CPU2 is up
[ 504.765719] smpboot: Booting Node 0 Processor 3 APIC 0x6
[ 504.768096] cache: parent cpu3 should not be sleeping
[ 504.768917] CPU3 is up
[ 504.771282] ACPI: Waking up from system sleep state S3
[ 504.790007] ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
[ 504.790055] pcieport 0000:00:1c.7: System wakeup disabled by ACPI
[ 504.790097] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 504.790130] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
[ 504.790158] PM: noirq resume of devices complete after 18.442 msecs
[ 504.790438] PM: early resume of devices complete after 0.248 msecs
[ 504.790626] pcieport 0000:00:1c.4: System wakeup disabled by ACPI
[ 504.790677] usb usb5: root hub lost power or was reset
[ 504.790678] usb usb6: root hub lost power or was reset
[ 504.792657] tg3 0000:03:00.0 enp3s0: Link is down
[ 504.853346] rtc_cmos 00:02: System wakeup disabled by ACPI
[ 504.853865] serial 00:06: activated
[ 504.855289] sd 2:0:0:0: [sda] Starting disk
[ 504.855304] sd 3:0:0:0: [sdb] Starting disk
[ 505.167929] ata7: SATA link down (SStatus 0 SControl 300)
[ 505.168077] ata8: SATA link down (SStatus 0 SControl 300)
[ 505.227852] ata5: SATA link down (SStatus 0 SControl 300)
[ 505.227868] ata6: SATA link down (SStatus 0 SControl 300)
[ 505.227885] ata1: SATA link down (SStatus 0 SControl 300)
[ 505.227904] ata2: SATA link down (SStatus 0 SControl 300)
[ 505.227920] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 505.228478] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 505.228480] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 505.228482] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 505.228708] ata3.00: supports DRM functions and may not be fully accessible
[ 505.236331] ata3.00: disabling queued TRIM support
[ 505.240993] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 505.240995] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 505.240996] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 505.241220] ata3.00: supports DRM functions and may not be fully accessible
[ 505.248841] ata3.00: disabling queued TRIM support
[ 505.249738] usb 5-1: reset full-speed USB device number 2 using xhci_hcd
[ 505.253066] ata3.00: configured for UDMA/133
[ 505.253141] ata3.00: Enabling discard_zeroes_data
[ 506.845522] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 506.856069] ata4.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 506.856071] ata4.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 506.856073] ata4.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 506.915860] ata4.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 506.915863] ata4.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 506.915865] ata4.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 506.952740] ata4.00: configured for UDMA/133
[ 507.807435] tg3 0000:03:00.0 enp3s0: Link is up at 1000 Mbps, full duplex
[ 507.807436] tg3 0000:03:00.0 enp3s0: Flow control is on for TX and on for RX
[ 507.807438] tg3 0000:03:00.0 enp3s0: EEE is enabled
[ 526.032945] usbhid 5-1:1.2: reset_resume error -110
[ 526.033090] PM: resume of devices complete after 21243.710 msecs
[ 526.033301] PM: Finishing wakeup.
[ 526.033302] Restarting tasks ...
[ 526.033467] pci_bus 0000:05: Allocating resources
[ 526.033487] pci 0000:04:00.0: bridge window [io 0x1000-0x0fff] to [bus 05] add_size 1000
[ 526.033490] pci 0000:04:00.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 05] add_size 200000 add_align 100000
[ 526.033493] pci 0000:04:00.0: bridge window [mem 0x00100000-0x000fffff] to [bus 05] add_size 200000 add_align 100000
[ 526.033497] pci 0000:04:00.0: res[14]=[mem 0x00100000-0x000fffff] res_to_dev_res add_size 200000 min_align 100000
[ 526.033499] pci 0000:04:00.0: res[14]=[mem 0x00100000-0x002fffff] res_to_dev_res add_size 200000 min_align 100000
[ 526.033501] pci 0000:04:00.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[ 526.033503] pci 0000:04:00.0: res[15]=[mem 0x00100000-0x002fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[ 526.033505] pci 0000:04:00.0: res[13]=[io 0x1000-0x0fff] res_to_dev_res add_size 1000 min_align 1000
[ 526.033507] pci 0000:04:00.0: res[13]=[io 0x1000-0x1fff] res_to_dev_res add_size 1000 min_align 1000
[ 526.033510] pci 0000:04:00.0: BAR 14: no space for [mem size 0x00200000]
[ 526.033511] pci 0000:04:00.0: BAR 14: failed to assign [mem size 0x00200000]
[ 526.033514] pci 0000:04:00.0: BAR 15: no space for [mem size 0x00200000 64bit pref]
[ 526.033515] pci 0000:04:00.0: BAR 15: failed to assign [mem size 0x00200000 64bit pref]
[ 526.033517] pci 0000:04:00.0: BAR 13: no space for [io size 0x1000]
[ 526.033518] pci 0000:04:00.0: BAR 13: failed to assign [io size 0x1000]
[ 526.033521] pci 0000:04:00.0: BAR 14: no space for [mem size 0x00200000]
[ 526.033523] pci 0000:04:00.0: BAR 14: failed to assign [mem size 0x00200000]
[ 526.033525] pci 0000:04:00.0: BAR 15: no space for [mem size 0x00200000 64bit pref]
[ 526.033526] pci 0000:04:00.0: BAR 15: failed to assign [mem size 0x00200000 64bit pref]
[ 526.033529] pci 0000:04:00.0: BAR 13: no space for [io size 0x1000]
[ 526.033530] pci 0000:04:00.0: BAR 13: failed to assign [io size 0x1000]
[ 526.033533] pci 0000:04:00.0: PCI bridge to [bus 05]
[ 526.046611] done.
[ 526.046622] video LNXVIDEO:00: Restoring backlight state
[ 526.203481] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[ 526.358290] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[ 529.389918] tg3 0000:03:00.0 enp3s0: Link is up at 1000 Mbps, full duplex
[ 529.389940] tg3 0000:03:00.0 enp3s0: Flow control is on for TX and on for RX
[ 529.389942] tg3 0000:03:00.0 enp3s0: EEE is enabled
[ 529.389961] IPv6: ADDRCONF(NETDEV_CHANGE): enp3s0: link becomes ready
[ 538.107665] usb 5-1: USB disconnect, device number 2
[ 538.109247] hid-generic 0003:04D9:A0CD.0002: usb_submit_urb(ctrl) failed: -19
[ 539.151869] usb 5-1: new full-speed USB device number 3 using xhci_hcd
[ 539.366001] usb 5-1: New USB device found, idVendor=04d9, idProduct=a0cd
[ 539.366003] usb 5-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 539.366005] usb 5-1: Product: USB Keyboard
[ 539.371653] input: USB Keyboard as /devices/pci0000:00/0000:00:1c.7/0000:06:00.0/usb5/5-1/5-1:1.0/0003:04D9:A0CD.0006/input/input16
[ 539.428241] hid-generic 0003:04D9:A0CD.0006: input,hidraw0: USB HID v1.11 Keyboard [USB Keyboard] on usb-0000:06:00.0-1/input0
[ 549.583676] hid-generic 0003:04D9:A0CD.0007: usb_submit_urb(ctrl) failed: -1
[ 549.583704] hid-generic 0003:04D9:A0CD.0007: timeout initializing reports
[ 549.583903] input: USB Keyboard as /devices/pci0000:00/0000:00:1c.7/0000:06:00.0/usb5/5-1/5-1:1.1/0003:04D9:A0CD.0007/input/input17
[ 549.643667] hid-generic 0003:04D9:A0CD.0007: input,hiddev0,hidraw3: USB HID v1.11 Keyboard [USB Keyboard] on usb-0000:06:00.0-1/input1
[ 549.646826] hid-generic 0003:04D9:A0CD.0008: hiddev0,hidraw4: USB HID v1.11 Device [USB Keyboard] on usb-0000:06:00.0-1/input2
J'ai réussi à résoudre ce problème en ajoutant une simple chaîne pour l'option de démarrage.
Poing de tous, terminal ouvert et type
lsusb
cette commande affichera les périphériques USB. La clé Aukey KM-G9 est nommée Holtek Semiconductor, Inc. notez le ID, dans mon cas, il s'agit de 04d9: a0cd, il est divisé en deux par deux points (:)
Ensuite, tapez sur le terminal:
Sudo gedit /etc/default/grub
Ici nous avons la configuration de grub, soyez prudent.
Modifiez GRUB_CMDLINE_LINUX_DEFAULT avec ce type de chaîne:
usbhid.quirks=0x*ID_before_colon*:0x*ID_after_colon*:0x00000008
enregistrer le fichier, puis dans le terminal:
Sudo update-grub
Redémarrez l'ordinateur
cela devrait résoudre cette situation étrange. Je pense que c'est quelque chose lié à la compatibilité du clavier avec le noyau Linux.